INPUTS:
channel 1 and 2: switchable instrument or microphone input as combi-socket, XLR + jack ¼” (6.35 mm) and clip indicators, min. dynamic headroom: 8 dB
line mode: high impedance jack input for instruments (pick-ups directly), unbalanced and line-level sources
impedance: 2.2 Meg
sensitivity: 22 mV (–33 dBV) (high/low attenuator: –10 dB via jumper)
equivalent input noise: A-weighted: 1 uV (–120 dBV)
mic mode: XLR- , balanced and stereo jack socket, unbalanced
impedance: XLR, balanced: 1.2 kOhm
impedance: jack, unbalanced: 2.7 kOhm
sensitivity: 3.3 mV (–50 dBV)
voice filter: –10 dB at 270 Hz (referred to 10 kHz)
equivalent input noise: A-weighted: 0.8 uV (–122 dBV)
phantom power: (XLR only): 48 V, max. 10 mA, short-circuit protected
return: unbalanced jack input, ¼” (6.35 mm), pre-master
sensitivity: 320 mV (–10 dBV)
impedance: 19.7 kOhm (note: impedance changes to 4.7 kOhm when external effect is switched OFF)
aux in: TRS stereo input, 3.5mm
OUTPUTS:
phones: headphones, jack socket, stereo, L/R connected, ¼” (6.35 mm)
input Impedance: 470 Ohm (common for L and R)
(!) Please note: Use TRS (Stereo Jacks) only. Does not work with mono jacks, and When plugged in, internal speaker is muted!
send: jack socket, unbalanced, ¼” (6.35 mm), pre master, output voltage: 1.4 V (+3 dBV)
line out 1 and 2: jack socket, unbalanced, preamp out, ¼” (6.35 mm), post effect, post EQ and master
output voltage 2: 1.74 V (+3 dBV)
output voltage 1: 0.33 V (-4.6 dBV)
DI-out 1 and 2: balanced XLR socket, pre/post EQ (sitchable by jumper) post effect and master
1 = ground 2 = positive 3 = negative
differential output voltage: 140 mV (–17 dBV)
FOOTSWITCH
footswitch: TRS jack socket ¼” (6.35 mm) to connect latching dual foot switch.
tip = built-in effect on/off, ring = parameter adjust or additional effect on/off , sleeve = common (ground)
(!) Please note: Effect is OFF when the footswitch is ON.
EQ - Tone Controls
channel 1:
tone: –3 dB at 700 Hz, +7 dB at 8 kHz
bass: 8 dB at 100 Hz (shelf type)
middle: 6 dB at 800 Hz
treble: 8 dB at 10 kHz (shelf type)
channel 2:
hpf filter: 40Hz to 350 Hz,
bass: 8 dB at 100 Hz (shelf type)
middle: 6 dB at 800 Hz
treble: 8 dB at 10 kHz (shelf type)
EFFECTS
effect presets: 1: reverb long, 2: reverb short, 3: chorus, 4: custom delay, 5: my delay, 6: tap n’ delay, external effect: parallel effect loop (see also send and return)
efx pan: blends both internal and external effects between channels 1 and 2,
POWER SECTION
power amp: 75 W / 4 ohm, DMOS, monolithic I.C. dynamic range, A-weighted: 92 dB
analog signal processing: dedicated equalizer, subsonic filter, adaptive peak limiter
limiter threshold: 60 W
speaker system: 8” (200 mm) twin cone full-range speaker, bass reflex enclosure
mains power: mains voltage (depending on model): 100, 120, 230, or 240 V AC, 50–60 Hz
power consumption: max. 200 W
mains fuse: 5 x 20 mm T 1A L /250 V for 230 and 240 V 5 x 20 mm T 2A L /250 V for 100 and 120 V
GENERAL
cabinet: 12 mm (0.47”) plywood
finish: polyester black spatter finish
dim: 265 mm (10.43“) height, 325 mm (12.8“) width, 245 mm (9.65“) depth
weight, net: 7.5 kg (16.5 lbs) 13